TYPICAL SCENARIOS28 parts, 28 ways to measure
Each entry follows public standards: the part and the problem first, then how we measure, which standard applies, and what came out. Deliberately free of marketing language — compare it with your own part.
01Automotive
Carburised gears: disputed case depth
- Part
- 20CrMnTi carburised gear, module 3, 0.6–0.9 mm required
- Problem
- Supplier measured 0.82 mm, OEM re-checked 0.61 mm — two verdicts on one batch, line stopped pending arbitration.
- Approach
- ZHVST-30F micro-Vickers system with motorised stage; one point every 0.05 mm from the surface per GB/T 9450, depth taken at 550 HV. Specimens cut on the ZQ-300F, mounted in the ZXQ-50, polished on the ZMP-3000.
- Standard
- GB/T 9450, ISO 2639
- Outcome
- Both parties re-measured on the same machine, specimen and parameters; spread narrowed to 0.03 mm and the case closed in three days without rejecting the batch.
02Bearings
Rings: sampling rate cannot keep up
- Part
- GCr15 bearing rings, 50,000 pcs/month
- Problem
- Only three parts were hardness-tested — under 5% coverage — and soft spots surfaced at assembly.
- Approach
- HRS-150 digital Rockwell tester gives a direct HRC reading in 8 s per part; suspect parts go to the ZQ-300F for sectioning and the 4XC-ST for structure review. Hardness distribution logged per furnace load.
- Standard
- GB/T 230.1, GB/T 18254
- Outcome
- Coverage raised to 30% while cost per part fell; soft batches are now stopped in heat treatment.
03Aerospace
Thermal-spray coatings: cross-section hardness and bonding
- Part
- Superalloy substrate with WC-Co / ceramic coating, 150–400 μm
- Problem
- Surface hardness alone cannot reveal internal porosity or interfacial cracks, so spalling stayed unexplained.
- Approach
- ZQ-300F low-speed precision cutting prevents edge chipping, ZXQ-50 cold mounting protects the edge, ZMP-3000 prepares the section stepwise, and the 4XC-ST inspects the interface. ZHVST-30F with 50 gf measures every 20 μm across the section.
- Standard
- GB/T 4340.1, ASTM E384, GB/T 9796
- Outcome
- A three-zone hardness profile (coating, interface, substrate) quantified the porous layer, giving spray parameters a comparable basis.
04Fasteners
High-strength bolts: decarburisation and brittle failure
- Part
- Grade 10.9 M12 bolts, quenched and tempered
- Problem
- Brittle fracture after three months in service with no visible defect — decarburisation suspected but unproven.
- Approach
- ZQ-300F sections along the axis, ZXQ-50 protects the thread root, ZMP-3000 polishes, and the 4XC-ST measures decarburisation depth; ZHVST-30F runs a 20 gf gradient from the surface. Judged to GB/T 3098.1.
- Standard
- GB/T 3098.1, ISO 898-1, GB/T 224
- Outcome
- Full decarburisation of 0.06 mm at the thread root confirmed an atmosphere problem; 120,000 bolts in the batch were screened.
05Mould & die
H13 cavities: hardness lost during polishing
- Part
- H13 die-casting cavity, 46–50 HRC required
- Problem
- Occasional early washout after polishing, yet every incoming hardness report passed — the culprit process stayed hidden.
- Approach
- HVS-5 Vickers tester takes 1 kgf points on the cavity surface and on polished areas; ZMP-3000 re-polishes and the 4XC-ST checks for tempering from overheating. Hardness compared at identical positions before and after polishing.
- Standard
- GB/T 4340.1, NADCA #207
- Outcome
- Excess polishing pressure had softened the surface by 3–4 HRC; switching to low pressure and multiple passes cut washout by 70%.
06Third-party labs
Angle metrology: traceable autocollimator readings
- Part
- Granite surface plates and machine guideways, straightness / flatness
- Problem
- Customers asked for an angle certificate with uncertainty; the existing optical instruments could not be traced.
- Approach
- ZY-20 autocollimator (±60″ / 0.2″) with a bridge plate in steps, straightness evaluated by minimum zone; a polygon prism cross-checks the instrument to build an internal calibration chain.
- Standard
- JJF 1110, GB/T 20920, JJG 117
- Outcome
- Certificates are accepted directly by customers, the internal calibration interval went from fixed half-yearly to on-demand, and outsourcing costs fell by two thirds.
07Forging
Large shafts: cutting distortion scraps the specimen
- Part
- 42CrMo forged shaft, Ø180 mm × 1.2 m
- Problem
- An ordinary abrasive saw left blue temper colours and a 1.5 mm taper; 3 mm had to be ground away and the specimen was effectively lost.
- Approach
- Moved to a ZQ-500F with a large wheel, dual coolant and 1.5 mm/min feed, sectioned in steps with both ends supported; faces finished on a ZY-200.
- Standard
- GB/T 13298, ASTM E3
- Outcome
- Taper within 0.2 mm and no temper colours; preparation time fell from 40 to 15 minutes per piece.
08Battery & electronics
Electrode foils: any blade curls the edge
- Part
- 8 µm copper and 12 µm aluminium foils, coated and uncoated zones
- Problem
- Abrasive cutting curled the foil and peeled the coating, so thickness and interface could not be measured.
- Approach
- ZY-100E diamond wire saw at low feed with no mechanical squeezing, held in a chilled fixture, then cold mounted.
- Standard
- GB/T 13298, ISO 19700
- Outcome
- Straight cut, no curl, intact coating interface; coating thickness and interface defects became measurable.
09Cemented carbide
YG grades: cobalt pools dragged out by polishing
- Part
- YG8 inserts, 1.5 µm grain size
- Problem
- Hand polishing with too much force removed cobalt and left pits that were read as porosity; batches did not agree.
- Approach
- A ZMP-3000 one-touch program with resin-bond diamond discs, low force, short steps and a 1 µm diamond finish, verifying each step under the microscope.
- Standard
- GB/T 3488, ISO 4499
- Outcome
- Cobalt pools preserved and porosity ratings repeatable within 0.2 of a class across three specimens.
10Heat treatment
Nitrided layers: the edge is always rounded away
- Part
- 38CrMoAl nitrided piston rod, case 0.25 mm
- Problem
- After mounting the edge was chamfered and the compound layer vanished, so case depth read 30% low or not at all.
- Approach
- ZXQ-50 hot mounting to protect the edge, ZMP-1000 with soft cloths below 10 N for 60 s per step, ZD-300 vibratory polishing for the final finish.
- Standard
- GB/T 11354, ISO 6336
- Outcome
- Edge retention clearly improved and case depth repeated within 0.02 mm.
11Fasteners & wire
M6 bolts: the thread root disappears
- Part
- Grade 10.9 M6 bolts, 1 mm pitch
- Problem
- Specimens were too small to hold and the root was polished flat, so decarburisation and folds could not be judged.
- Approach
- Six pieces mounted at once in ZXQ-50 with phenolic at 140 °C and 25 MPa, ground to the pitch diameter and etched.
- Standard
- GB/T 3098.1, GB/T 224
- Outcome
- Root profile preserved, decarburisation and folds visible, 30 minutes for a batch of six.
12Casting
Heavy castings: bulk hardness will not settle
- Part
- HT250 machine-tool bed, 1.8 t, critical faces already machined
- Problem
- A portable Leeb gauge scattered on the rough face and disagreed with the foundry by 30 HBW.
- Approach
- HBT/HBST-3000 with a prepared Ø60 flat, 10 mm ball, 3000 kgf, 15 s dwell, indentation read by the image system.
- Standard
- GB/T 231.1, ISO 6506-1
- Outcome
- Agreement within ±10 HBW; acceptance no longer depends on feel.
13Cutting tools
Coated tools: coating and substrate hardness must be separated
- Part
- Carbide end mill with 3 µm TiAlN coating
- Problem
- Measuring at 1 kgf punched through the coating into the substrate, so the coating was never characterised.
- Approach
- HVF-1000D at 0.05 kgf for the coating and 0.5 kgf for the substrate, with automatic indentation measurement and photo records; coating thickness measured in the same field.
- Standard
- GB/T 4340.1, ISO 6507-1
- Outcome
- Coating 2800 HV0.05 and substrate 1600 HV0.5, both traceable and comparable between deliveries.
14Springs
Spring steel: decarburisation halves fatigue life
- Part
- 60Si2Mn coil spring, 12 mm wire
- Problem
- Bench testing failed at 80,000 cycles from a surface origin while hardness passed, leaving no explanation.
- Approach
- Sectioned on a ZQ-50S, mounted in ZXQ-50 and traversed on an HVS-1000 every 0.05 mm, with 4XC-ST examination of the fully and partially decarburised zones.
- Standard
- GB/T 224, GB/T 18983
- Outcome
- Fully decarburised 0.05 mm and partially 0.12 mm; the atmosphere dew point was corrected and life returned to 300,000 cycles.
15Machine tools
Gantry guideways: a 3 m straightness dispute
- Part
- X-axis guideway, 3.2 m long
- Problem
- Spirit-level readings drifted with temperature and handling, and the builder and user disagreed by 0.02 mm/m.
- Approach
- ZY-30 autocollimator with a 200 mm bridge, 16 equally spaced points measured forward and back and evaluated by the minimum-zone method after a 2 h warm-up run.
- Standard
- GB/T 11336, ISO 230-1
- Outcome
- Both parties measured 0.018 mm full length, agreeing within 0.004 mm, and the machine was accepted first time.
16Construction
High-strength bolts: failure in the gripped thread
- Part
- M20 grade 10.9 bolts, tensile strength ≥1040 MPa
- Problem
- Specimens broke in the gripped thread, so the test was invalid even after changing grips.
- Approach
- WAW-600 hydraulic universal machine with bolt grips and an extensometer for Rp0.2, loaded at 10 MPa/s to GB/T 228.1.
- Standard
- GB/T 228.1, GB/T 3098.1
- Outcome
- Failure in the shank, 1085 MPa tensile and 940 MPa Rp0.2, usable for routine inspection.
17Welded structures
Low-temperature steel: impact energy falls off fast
- Part
- Q345E welded joint for −40 °C service
- Problem
- Room-temperature impact of 120 J passed, but without a transition curve the −40 °C behaviour was unknown.
- Approach
- JB-300B with a low-temperature bath, three specimens every 10 °C from +20 to −60 °C, plotted as energy against temperature.
- Standard
- GB/T 229, ISO 148-1
- Outcome
- Full transition curve obtained; 47 J at −40 °C against a 34 J requirement, and the welding procedure was frozen.
18Powder metallurgy
Sintered parts: porosity mistaken for inclusions
- Part
- Iron-base PM gear, 7.0 g/cm³ density
- Problem
- In bright field both pores and inclusions are black, so porosity was rated as inclusions and density was rejected.
- Approach
- 4XC-ST bright and dark field of the same field: pores glow in dark field and change with focus, inclusions do not; porosity then quantified by image analysis.
- Standard
- GB/T 5163, ISO 2738
- Outcome
- Separated true inclusions at class 0.5 from 6.8% porosity and avoided a wrongful rejection.
19Heat exchangers
Thin-wall tubes: flattened by the vice, ovality lost
- Part
- 20# steel heat-exchanger tube, φ19×2 mm, 300 mm long
- Problem
- Vice clamping plus abrasive cutting ovalised the tube end; wall thickness and roundness were unusable, while wire cutting could not get through.
- Approach
- ZQ-1000S auto-feed cutter with V-soft jaws and an internal mandrel, finer wheel, 0.8 mm/min feed, single-pass cutting without clamping distortion.
- Standard
- GB/T 13298, GB/T 246
- Outcome
- Ovality within 0.1 mm, wall thickness measurable, 3 min per cut.
20Automotive
Carburised gears: blue tint made the case look shallow
- Part
- 20CrMnTi carburised and hardened gear, 0.8 mm effective case
- Problem
- Insufficient cooling left temper colours at the cut; the case edge was softened and measured only 0.5 mm.
- Approach
- ZQ-300F with dual coolant jets straight into the cut, feed reduced to 1.2 mm/min with step feeding; 0.2 mm lightly ground off before measuring.
- Standard
- GB/T 9450, ISO 2639
- Outcome
- No temper colours; case re-measured 0.78 mm, matching the heat-treatment report.
21Surface engineering
Thermal-spray coatings: the whole layer lifted off
- Part
- WC-12Co coating, 300 μm, on 45# steel
- Problem
- Hot mounting opened the coating/substrate interface and the edge broke away during grinding, so thickness and porosity could not be measured.
- Approach
- Vacuum impregnation plus cold epoxy mounting, 24 h cure; wire-cut sectioning; minimum pressure and a final 1 μm step of only 20 s.
- Standard
- GB/T 9790, ASTM B748
- Outcome
- Interface intact, coating 305 μm, porosity 1.2%, no interfacial cracks.
22Non-ferrous
Copper: polished surface looks fogged
- Part
- T2 copper plate, 3 mm, grain size 30 μm
- Problem
- Mechanical polishing left a foggy surface with blurred boundaries; more pressure only smeared the second phase.
- Approach
- ZMP-1000 low-pressure program: 1200# then 3 μm diamond for 25 s and 0.05 μm silica for 10 s; etched in ferric chloride/HCl for 8 s.
- Standard
- GB/T 13298, GB/T 6394
- Outcome
- Mirror surface, clear boundaries, grain size 8.5, repeatable across three runs.
23Aerospace
TC4 titanium: scratches that will not go away
- Part
- TC4 titanium forging, 12 mm thick
- Problem
- Titanium smears and conducts heat poorly, so papers clogged quickly and every pass added scratches; water rinsing left drying marks.
- Approach
- ZMP-3000 with fresh papers, low pressure and 40 s per step; 3 μm diamond on short-nap cloth, ethanol rinse and warm-air dry.
- Standard
- GB/T 6611, ASTM E3
- Outcome
- Scratches removed, α/β interfaces clear, no drying marks.
24Welding consumables
Fine wires: one at a time is too slow
- Part
- φ0.8 mm flux-cored welding wire, 20 sections per batch
- Problem
- Single mounting was slow and the wires sat at an angle, so the polished plane missed the centre.
- Approach
- A shop-made 12-hole fixture loaded 12 wires at once into the ZXQ-50 hot press; the fixture keeps them parallel so one grind reaches all centres.
- Standard
- GB/T 13298, GB/T 17493
- Outcome
- 12 wires per press cycle, perpendicular sections, 20 wires in 40 min.
25Fasteners
Grade 12.9 bolt: decarburised depth kept measuring short
- Part
- M12 grade 12.9 bolt, hardened and tempered
- Problem
- The decarburised layer at the thread root is only tens of microns; indents spaced too widely missed the turning point and the depth was under-reported.
- Approach
- ZQ-50S precision cutting along the thread root, ZXQ-5A hot mounting for edge retention, ZMP-2000 to 1 μm; HVT-1000A HV0.5 indents every 0.05 mm from the root inwards, full + partial decarburisation judged per GB/T 224.
- Standard
- GB/T 224, GB/T 3098.1
- Outcome
- Full decarburisation 18 μm, total 42 μm — matching the metallographic cross-check, batch accepted.
26Advanced ceramics
Zirconia: too much polish pressure changed the hardness
- Part
- Y-TZP zirconia, 3Y-stabilised, 10×10×5 mm sintered tiles
- Problem
- Heavy polish pressure induced a tetragonal-to-monoclinic transformation layer; HV readings scattered low, giving "two hardnesses" in one batch.
- Approach
- ZY-100E low-speed diamond cutting, cold epoxy mounting; ZMP-2000 low-pressure long polish to 1 μm, HV1 measured unetched; indentation KIC for fracture toughness.
- Standard
- GB/T 16534, GB/T 6569
- Outcome
- Hardness stable at 1250±30 HV1, indentation KIC = 5.8 MPa·m^0.5, batch scatter under 5%.
27Electronics
MLCC capacitors: dielectric layers impossible to count
- Part
- 0402 MLCC, ~2 μm dielectric layers, 300+ layers
- Problem
- Chipping at the cut face fractured every layer in that zone — no way to count layers or measure thickness.
- Approach
- ZQ-50S slow precision cut, vacuum epoxy infiltration 12 h, ZMP-2000 stepwise diamond polish; layer thickness distribution measured at 1000× on the 6XC-ST image analysis system.
- Standard
- GB/T 13298, IEC 60384
- Outcome
- Intact cut face, dielectric thickness 1.9–2.2 μm uniform, no interlayer cracks found.
28Gears
Carburised gear: effective case depth acceptance
- Part
- 20CrMnTi carburised gear, module 4, case target 0.9 mm
- Problem
- The first sample was cut with a burnt face; the hardness gradient was wrong from the first point and the report was rejected.
- Approach
- ZQ-500F low-speed constant-torque cutting with flood cooling; HRC spot checks on the cut face before sectioning; HVST-1000C HV1 indents every 0.1 mm from the flank, effective depth at 550 HV1 per GB/T 9451.
- Standard
- GB/T 9451, GB/T 34807
- Outcome
- Effective case depth 0.86–0.92 mm, core hardness 42 HRC, smooth gradient, lot accepted.
These are typical conditions compiled from public standards, without customer names or commercial data. Samples of comparable parts are welcome for testing.